Wavlink WiFi router helps to extend the range of WiFi signals by wirelessly or wired. Here are the most common issues that you face during & after doing the Wavlink router setup with the modem, along with their solution tips. Read all information of this page briefl
Common Issues
There are several issues which you face, see all the issues one by one.
Unable Or Fail To Access Wavlink Login Page
- Fill in the wrong Wavlink default URL or IP address in the chrome address bar.
- Computer or laptop not connected with the Wavlink router default WiFi network.
- Due to browser cache and cookies.
Facing Slow Speed Internet
- Lots of WiFi devices connect with the Wavlink WiFi router network.
- Router is not located at the central location.
- Wavlink router is receiving slow WiFi signals from the internet service provider.
WiFi Keep Disconnecting
- Due to overlapping of WiFi channels.
- Strength of the WiFi signals is weak.
- Wavlink router software or firmware is outdated.
Wavlink Router Not Turned On
- Power outlet is not working properly.
- Did not complete the hardware process, before setting it up.
Fail To Connect More Devices With Router WiFi
- Limit of WiFi connected devices is complete.
- Due to DHCP settings.
Wavlink WiFi Router Firmware Outdated
- Internet connection drops due to outdated firmware.
- Installed incorrect firmware file.
WiFi Signal Not Reach At All Areas
- Router is located near to the metal appliances or thick walls.
- Placement of the Wavlink router is not ideal.
The above are the few issues which you face during & after Wavlink router setup. To fix all that issues now, try the below fixation tips.
Issue Fixation Tips
Restart Wavlink Router
- Take out the Wavlink WiFi router power plug from the working power socket.
- After that, press the power button to turn it off and wait for a while.
- Later, place the router plug back in the socket and turn on the Wavlink router.
By trying this restart solution tip you can fix the connectivity issue or temporary glitches with Wavlink router.
Look Up Wavlink Router Settings
To check the Wavlink WiFi router settings, go to its web page through wifi.wavlink.com. After that, look up all the settings to ensure that everything is configured correctly.
Verify All Cables
Sometimes issues might happen due to the network cables which are connecting your WiFi device such as laptop or computer with router. Must verify that all the cables must connect perfectly. If any cable is there which is damaged then replace it with the new one.
Download Wavlink Latest Firmware
Follow the below directions to update Wavlink router software,
- Take a WiFi device and connect it with Wavlink router default network.
- After that, open chrome and type IP address to access Wavlink web management page.
- Later, go to settings and tap on network administration.
- Under that, click on the software install option.
- Further, if there any latest software file is pending then install it.
- File installation process takes 15 to 20 minutes to complete.
Change Wavlink Router Placement
By changing the placement of the router, you can enjoy seamless internet speed. Make sure Wavlink WiFi routers don’t be located near metal or electronic obstacles.
Place Router In Another Power Socket
Verify that the Wavlink router must be plugged in the working power socket. If the socket is not working properly, then take out the Wavlink router power plug and put it into the new power socket which is in good working condition.
Reset Wavlink Router
If you fail to fix Wavlink router issues by trying the above troubleshooting tips, then try this last method.
- Early, search for the reset button on your router.
- After that, grab a pin and press the reset button with it for 15 seconds.
- Further, wait to turn off all Wavlink router LEDs.
- Hence, your Wavlink router unit is now completely reset.
After reset Wavlink WiFi router, do the login and configuration process again.
Access To Wavlink Router Web Page
- Early, place Wavlink router power plug in working socket.
- After that, connect the WiFi device with the default network.
- Now, launch chrome on a connected WiFi device and type wifi.wavlink.com in the chrome URL bar.
- Fill in login page details.
- Once logged in, you can change settings that you want in your Wavlink router.
Setup Wavlink WiFi Router With Modem
- Early, power off the modem and take it out from the socket.
- Now, use ethernet wire to connect Wavlink router WAN port with modem LAN port.
- Further, power on the modem and wait for it to boot up.
- Next, plug in the router and turn it on.
- Later, connect WiFi devices with the Wavlink router by using cable or wirelessly.
- Launch chrome and type 192.168.10.1. Hit enter.
- Interject all login details.
- Once you logged in to the Wavlink router web page, click on the internet setting or WAN setup option.
- Based on your Internet service provider, pick the correct connection type.
- After that, change the SSID (WiFi network name).
- Set a strong WiFi password.
- At the end, save all changes and power cycle or reboot your Wavlink router.
After considering the direction or information of this informative page, we hope you can fix the common Wavlink router issues by trying the apart solution tips. Contact the Wavlink team to get more help.
